VE6DOK Search
Start Here

All Project Sites Results

Doppler shift on ham radio: satellites, moonbounce, aurora and more

Weekly blog: a new post every Wednesday. Don’t forget to sign up for our free weekly newsletter on Substack: sign up here.Our four sites each post once a week: West Lethbridge Weather on Monday, Lethbridge Weather on Tuesday, VE6DOK on Wednesday and Dok-Tor Harddrive on Thursday, with the Prairie Signals newsletter rounding up the week on Friday.

If you’ve ever worked a satellite and had the signal slide right off frequency in the middle of a contact, you’ve met the Doppler shift. It’s the same effect that makes an ambulance siren drop in pitch as it goes by, and the same one weather radar uses to see the wind inside a storm. For hams it shows up in a few places: some are a nuisance, and some are worth listening for.

The basic idea

When a transmitter is moving toward you, its radio waves arrive bunched together, so you hear it on a slightly higher frequency. When it’s moving away, the waves are stretched out and it shows up a little lower. The amount depends on two things:

  • How fast it’s moving toward or away from you. Sideways motion doesn’t count.
  • The frequency. The shift is a fixed fraction of the operating frequency, so the higher the band, the bigger the shift in hertz.

The fraction is the speed divided by the speed of light. For anything on the ground that’s far too small to notice. For something in orbit, it isn’t.

Satellites: where you really notice it

Amateur satellites and the International Space Station orbit at roughly 7.5 km/s (about 27,000 km/h, or 17,000 mph). As one comes up over your horizon it’s racing toward you, and as it goes down on the other side it’s racing away. The shift you have to deal with is roughly:

  • 2 metres (145 MHz): up to about ±3.5 kHz
  • 70 cm (435 MHz): up to about ±10 kHz, three times as much because the frequency is three times higher
During a satellite pass the received frequency starts high, drops fastest at closest approach, and ends low +3.5 kHz (coming toward you) time during the pass closest approach:frequency changes fastest -3.5 kHz (going away) on freq
The received frequency during an overhead pass on 2 m. Rising, it starts high. Overhead, it changes fastest. Setting, it ends low.

The shift isn’t steady. It changes slowly when the satellite is low on the horizon and fastest when it’s closest to you, overhead on a high pass. That’s why a contact can be going fine and then suddenly drift away.

How hams deal with it

  • FM satellites, including the ISS: the 2 m side can usually be left alone, because FM is forgiving and ±3.5 kHz mostly still gets through. Correct the 70 cm side. Many operators store five memory channels about 5 kHz apart and step through them during the pass: high at the start, centre in the middle, low at the end.
  • SSB and CW satellites (linear transponders) need much finer tuning. The common rule is to adjust the higher-frequency side, since it drifts the most, and to listen to your own signal coming back through the satellite so you stay in the same spot as the station you’re working.
  • Computer control: programs such as Gpredict and SatPC32 predict the pass and retune a computer-controlled radio automatically, second by second.

Moonbounce (EME)

The Moon itself moves slowly, but the Earth turns under it, so your station is always moving toward or away from the Moon. Your signal also makes a round trip, so the effect counts twice. The shift is a few hundred hertz on 2 m, climbs to a few kilohertz on 23 cm (1296 MHz), and reaches tens of kilohertz on the microwave bands. EME software works it out for you, but you need to know which way to look for the echo.

On HF, it’s tiny but real

The ionosphere isn’t still. Its layers rise and fall, especially around sunrise and sunset, and a signal bouncing off a moving layer picks up a small Doppler shift, usually less than a few hertz. You’d never hear that on SSB, but the narrow digital modes notice it. That’s part of the reason FT8 and WSPR signals sometimes show a small frequency drift that has nothing to do with the transmitter.

Aurora: Doppler you can hear

Here in southern Alberta we get the occasional strong aurora, and on 6 m and 2 m hams can bounce signals off it. The glowing curtains are full of fast-moving electrons, and every part of the curtain moves at a different speed. The echoes come back smeared across a range of frequencies, so a clean CW note turns into a rough, hissing buzz. That’s why aurora contacts are mostly made in CW and why signals sound “fluttery.” It’s Doppler spreading in action.

Aircraft and meteors

  • Aircraft scatter: on VHF and the microwave bands, signals reflected off airliners can make long-distance contacts for a few seconds at a time. The plane’s speed shifts the echo, and you can hear it slide as the plane crosses the path.
  • Meteor scatter: a meteor’s trail of ionized gas reflects signals for a fraction of a second up to several seconds. The trail drifts in the upper winds, which can give the burst a small Doppler offset of its own.

The same physics as weather radar

Environment Canada’s weather radars use exactly this effect, in reverse. They measure the tiny Doppler shift of echoes coming back from raindrops to work out how fast the wind is blowing inside a storm, and to spot rotation that could become a tornado. Read more on our weather site: West Lethbridge Weather.

Was this page helpful?

Questions or ideas about this post? Email us at help@drhd.com. We read every one.

📻 Friend of VE6DOK: hamshack.ca, Canada’s ham radio marketplace, club directory and QSL Academy licence courses by Don Rosberg, VE7DXE.
Get all four of our sites in one free email every Friday: Prairie Signals
Hello! “Leadership is the ability to get a person to do what you want them to do, when you want it done, in a way you want it done, because they want to do it. (Dwight Eisenhower)”