A walk around Gary’s 2017 Ram 1500 as it’s set up in 2026: the radios, the wiring, the power panel and the truck itself. Tap any photo to see it full size. For what each piece does, see the main VE6CV Mobile: the Truck Station page.
After dark
The cab on a January night with the interior lights switched to red. Red light is easier on your night vision, so the radio displays stay readable without blinding you when you look back out the windshield.
Everything you see on the console is used: HF, VHF/UHF and DMR, with the mics and control heads all within reach of the driver’s seat.
After dark: the red glow and the topper lights
The same red interior light, seen from outside at dusk at the campground, makes the whole cab glow. And when the work lights on the topper come on, the truck lights up the whole site.
At dusk the cab lights up red from the inside.The exterior LED lights on the topper turn the whole campsite into a lit work area after dark.Through the windshield: the red-lit cab with the antennas up behind it.
The operating position
The centre console is the heart of the mobile station. Gary built it during the 2021 rewire, and the truck’s wiring was done by Wired by ITB in Coaldale.
What’s in the truck: Icom IC-7100 (all band, all mode, with D-STAR), Yaesu FTM-400 (VHF/UHF with WIRES-X), Kenwood TK-981 (900 MHz), Kenwood TKD-740HK (LADD, VHF and DMR), Cobra 148GTL (40-channel CB, AM/SSB), a Yaesu FTA-450 aircraft-band handheld, GMRS and amateur handhelds, an RFinder B1+ for DMR and radio over internet, and a weBoost 4G/5G cell booster. Antennas include a Tarheel 75A screwdriver for HF on the rear driver side, Larsen antennas on the roof and cowls for VHF/UHF, CB and 900 MHz, and the cell booster antenna on the roof. What each one is for is on the Radios and antennas page.
The whole dash and console, taken from the driver’s seat looking across to the passenger side.Close-up of the radios, mic clips and control heads.The commercial radios: the Kenwood TK-981 900 MHz (top, red display) and the Kenwood TKD-740HK for LADD, VHF and DMR (below). Note the “Wired” badge from the installer.The Icom IC-7100 control head (all band, all mode), with the chrome knobs of the Cobra 148GTL CB beside it. A separate head means the radio body can live out of the way while the controls stay in reach.A Yaesu FTA-450 aircraft-band handheld in its own mount, for listening to air traffic, ready to grab and walk away with.The RFinder B1+: an Android phone and DMR radio in one, with VHF/UHF plus radio over internet on 4G.
Power and wiring
A radio station is only as good as its power. The truck carries two 110 Ah 6 V AGM house batteries, a 2000 W inverter, a 40 A DC-DC charger and a 350 W solar panel on the topper roof. More on the Power and solar page.
The dash-mounted power panel: inverter remote, battery monitor and charge display, all where the driver can see them.Behind the scenes under the dash: fused power distribution, a 120 V outlet and the cable runs.The console at night, January 2026.
Outside the truck
The Leer topper, roof awning and rear drawer system turn the truck into a base camp, and the antenna mast mount on the rear corner gets an antenna up quickly when parked.
The Ram 1500 with its Leer topper and roof awning at Riverwood Campground.Front of the truck.The topper with the roll-out awning packed on the roof rail.The antenna mast mount on the rear corner.Close-up of the mast mount.Set up for the season at the campground.The rear drawers: coax, power cords and field gear, all with a place to live.Behind the seats: a storage cage and more gear.
Field Day and camp: the truck as base camp
For Field Day 2026 the truck became the whole station: the roll-out awning and side-wall shelter make a room along the side, the tailgate end becomes the operating table, and the antennas go up beside it. More on the Field Day and camp page.
Operating from outside the truck: The IC-7100’s main control head is built permanently into the console, so it stays put. Instead, Gary keeps a second control head with its own microphone and a 4.6 m (15 ft) extension cable. The radio body is under the front seat: he disconnects the console head’s cable there, plugs in the spare, and runs it out to the table. Custom screens on the back windows let him roll the windows down to route the cables, while keeping bugs out of the cab.
Field Day 2026 (June 27): a second IC-7100 control head on the table under the awning, with the laptop and a fan for the heat.Awning out and the side wall up along the truck.From the back: tailgate down, rear awning out and the shelter beside it.The full base camp: side-wall shelter and rear awning with poles and guy lines.The shelter attached along the side of the truck.Wide view of the camp, with a vertical HF antenna up.Inside the awning room: cot tent, chair, small table and coax.Folding tables in the shelter beside the open topper.The radio control head and laptop running rig control on the table at the truck.From under the awning: handheld and laptop on 14.300 MHz.Packed up and ready to roll: topper, roof rack, rolled awning and antennas.
Got a question about the install? Ask Gary on the air or in the Mobile HF Ham Radio Operators group on Facebook. Photos: Gary Wheeler, VE6CV, 2026.